email [email protected] | +86-21-58386256

the process of making slag

Slag - WikipediaIn principle, steelmaking is a melting, purifying, and alloying process carried out at approximately 1,600° C (2,900° F) in molten conditions. Various chemical reactions are initiated, either in sequence or simultaneously, in order to arrive at specified chemical compositions and temperatures.Steel Slag - User Guideline Asphalt Concrete - User ...Mar 08, 2016· This difference is dependent on the steel-making plant, steel-making process, specific furnace, steel slag processing, and storage strategies. For this reason, the use of steel slag aggregate must be considered on a specific steel-making furnace and processing basis, with recognition of the inherent variability of the slag production and the ...Steel Making Solutions - RHI MagnesitaMinimise Process Variations. Carryover slag variations in ladles are often the cause of a number of problems detrimental to processing and product quality. Unforeseen reoxidation reduces alloying yields and refining efficiency forcing the operator to deviate from the standard processing and take additional processing steps. The added oxygen ...Steelmaking and Refining | Introduction to ChemistryFor plain-carbon steel furnaces, as soon as slag is detected during tapping, the furnace is rapidly tilted back towards the deslagging side, minimizing slag carryover into the ladle. HIsarna Steelmaking. The HIsarna steelmaking process is a process of primary steelmaking in which iron ore is processed almost directly into steel.

Iron & Steel Making – Page 4 – Askmemetallurgy

Which one of the following process of steel making is also known as Thomas process. Acid Bessemer process Basic Bessemer process LD process Open hearth furnace Discuss Here. ... Reducing single slag practice Double slag practice Oxidizing single slag practice Argon oxygen decarburizer Discuss Here. 43. In the blast furnace process,in which of ...Steel-making processes - Materials DatabaseElectric arc process. The heat required in this process is generated by electric arcs struck between carbon electrodes and the metal bath (Fig. 1). Usually, a charge of graded steel scrap is melted under an oxidising basic slag to remove the phosphorus. The impure slag is removed by tilting the furnace.WHAT IS STEEL MAKING PROCESS: BRIEFLY EXPLAINJun 21, 2016· Primary Steel making Process. It is the process of making steel from carbon-rich molten pig iron. The process was introduced and developed in 1948 by Robert Durrer. However, VOEST and OAMG commercialized this method in 1952–53. ... Burnt lime or dolomite is fed well into the vessel to form slag. It absorbs impurities at the time of making steel.

The FINEX Process of Iron Making - Features, Merits and ...

The hot metal and slag produced in the melter gasifier is frequently tapped from the hearth similar to the blast furnace and COREX operations. Also refer : COREX Process of Iron Making - its Merits and Demerits. ZEWA or ZERO Waste Steel Shop | Zero Waste process of Steel MakingSteel-making processes - Materials DatabaseElectric arc process. The heat required in this process is generated by electric arcs struck between carbon electrodes and the metal bath (Fig. 1). Usually, a charge of graded steel scrap is melted under an oxidising basic slag to remove the phosphorus. The impure slag is removed by tilting the furnace.An Overview of Use of Linz-Donawitz (LD) Steel Slag in ...There are different types of slag produced in the steel-making process. These include furnace or tap slag, raker slag, synthetic or ladle slags. Figure 1 depicts a flowchart of the general flow and production of different slags in a modern steel plant. Following processing and metal recovery, the nonmetallic products from the furnace, raker and ...Direct reduced iron process - tec-scienceDirect reduced iron (DRI) process. In addition to the process route via the blast furnace process, there is another option for extracting crude steel from iron ores using the so-called direct reduced iron (DRI) process (secondary route).The starting point for the efforts to find an alternative to the blast furnace process was the relatively high process expenditure.The Steel Making IndustrySlag, the limestone and iron ore impurities collected at the top of the molten iron, make up the largest portion of ironmaking by-products. Sulfur dioxide and hydrogen sulfide are volatized and captured in air emissions control equipment and the residual slag is sold to the construction industry.

Emerging Technologies for Iron and Steelmaking

The IFCON process, developed by ISCOR in South Africa, is capable of producing steel directly from coal and iron ore. 1 In this process, coal and ore are added continuously to a channel type induction furnace containing a slag-metal bath. Electrical energy is supplied by the induction furnace for heating and stirring the bath.The FINEX Process of Iron Making - Features, Merits and ...The hot metal and slag produced in the melter gasifier is frequently tapped from the hearth similar to the blast furnace and COREX operations. Also refer : COREX Process of Iron Making - its Merits and Demerits. ZEWA or ZERO Waste Steel Shop | Zero Waste process of Steel MakingElectroslag Remelting Process: Part One :: Total Materia ...Electro Slag Remelting (ESR) process has been known since the 1930's, but it took approximately 30 years before it became an acknowledged process for mass production of high-quality ingots. It is a process used for remelting and refining of steels and special alloys which are used for critical applications in aircraft, thermal and nuclear power ...US900939A - Slag cement and process of making the same ...Slag cement and process of making the same. USA US900939A () Slag cement and process of making the same. ) USA () : : Slag cement and process of making the same. US () ...Properties and Uses of Steelmaking Slag – IspatGuruNov 14, 2018· Steelmaking slag is an integral part of the steelmaking process. It is produced during the separation of the liquid steel from impurities in steelmaking furnace and is a non-metallic by-product of steelmaking process. It occurs as a molten liquid melt and is a complex solution of silicates and oxides which solidifies upon cooling.Synthetic Slag for Secondary Steelmaking – IspatGuruMar 28, 2017· The principle of the process of using synthetic slag consists in making a contact on a large surface between the liquid steel and a slag having a composition selected to ensure an advanced steel deoxidation and desulphurization. Design of synthetic slag. Slag design in secondary metallurgy is crucial for the performance in steelmaking.Secondary steel making processes - LinkedIn SlideShareMar 19, 2015· CLU refers to the Creusot-Loire Uddeholm process. It also uses liquid steel from an electric arc furnace (EAF) or any other similar primary steel making furnace. The major development of the CLU process was the idea to use superheated steam as the diluting gas instead of argon (Ar) gas which is used in the AOD process. The presence of the steam ...The Ironmaking Process | New Zealand SteelThe slag is made up of a range of oxides and its formation is essential to remove undesirable elements such as silicon, titanium and sulfur. Phosphorous, another undesirable element in steelmaking, is not removed from the iron and it is therefore very important to minimize its presence in the feed materials right at the outset.

Jaw Crusher

Jaw Crusher

Jaw crusher machine is the necessary machine in sand making production line

Impact Crusher

Impact Crusher

Impact crusher has many unique advantages, and attracts much attention